CPU Module (10-CH 24VDC input & 6-CH relay output) Support Codesys

Model NO.
SC1107N
Specification
120mm(L)× 80mm(W)× 63mm(H)
Trademark
Chitic
Origin
China
Reference Price
$ 161.10 - 182.70
Contact Us

Product Description


CPU Module (10-CH 24VDC input & 6-CH relay output) Support Codesys

 

Technical Specifications

Support Codesys v3.5 SP13

 
CPU  Main parameter of electrical source
I/O
10-CH 24VDC input
6-CH Relay output 		Supply Voltage
220VAC @50Hz
Expansion capability Up to 20 modules can be extended (relay module is required) Allowance range
187~264VAC @50Hz
Storage capacity Program area : 400KB Maximum current
120mA
N Area : 8KB 
M Area : 5KB 		Output Voltage
24VDC
Power loss holding area : 2KB Output  Current
400mA
Timer Hardware timing : 1,
0.1ms ~ 500ms
No limit on software timing (min. 1ms) 		Short-circuit protection
800mA,24VDC output
Counter 16bit Communication interface 1*RS232, 2*RS485
Operating rate
0.06 μ s (Boolean operation instruction)
1*RJ45
Interrupt input
4
Communication protocol Serial MODBUS RTU protocol, custom protocol
Analog potentiometer
2 ,0~255
MODBUS TCP, 4 Server links
Input Channal Output Channal
Type of input P/M-lesend Type of output Relay
Input signal Rated voltage 24VDC Output signal Rated voltage 24VDC
or 24 ~ 230VAC
0 ~ 30V DC 5 ~30VDC
or 5 ~ 250VDC
Input signal (ON) 15~30VDC and
> 3 mA 		Common terminal output current summation < 5A
Input signal (OFF) 0~5VDC and
< 1mA 		Output contact capacity 2A, Impedance load
Input delay < 0.6ms (Rated input voltage) Switch delay < 10ms
Isolation method Optoelectronic isolation The isolation voltage between the coil and the contact 3000V AC, 1min, leak current 1mA
Isolation of pressure 1000VDC Isolation voltage between contacts 750V AC, 1min, leak current 1mA
Mechanical life of relay Without load, it can reach more than 10,000,000 times;
Rated resistance 2A load, up to more than 100,000 times
Dimensions and Mounting Work Environment
Dimensions
120mm(L)×80mm(W)×63mm(H)
Operating temperature 0 ~ +55ºC
Weight
380g
Storage temperature -40 ~ +70ºC
Way to install 35mm DIN rail Relative humnidity 5% ~ 95% Noncondensing
Panel mounting type



Main interface and terminal definitions

CPU Module (10-CH 24VDC input &amp; 6-CH relay output) Support Codesys
1. Switch: RUN and STOP are used to control the 2107N program to RUN and STOP. If the RS232 interface communication parameter of PCS1200 PROGRAMMABLE logic controller is modified, the program can only be downloaded by dial STOP.
2. Ethernet communication interface: RJ45 interface, which can be used for communication with touch screen, upper computer, cloud server, etc., supports MODBUS TCP protocol, and links four clients simultaneously.
3. Indicator light: RUN, COM and ERR are respectively used to display module operation, communication and fault status; I and Q are respectively used to indicate input and output status of each channel; ETH, C1 and C2 are respectively used to indicate communication status of A1B1, A2B2 and Ethernet interfaces (flashing indicates data receiving and receiving at corresponding interfaces).
4. RS232 communication interface: This interface is terminal wiring, which can be used for 2107N program download, communication with touch screen, upper computer, etc. It supports MODBUS RTU/ custom protocol, instruction library is RS232.lib;
5. RS485 communication interface: Two interfaces can be used to communicate with touch screen, upper computer, third-party instrument, etc. MODBUS RTU/ free protocol is supported. Instruction library is RS485. Lib and RS4853.lib respectively.
6. Module input terminal: it is composed of common terminal 1M and input point I, and the source/leakage connection method can be adopted.
7. 24VDC power supply outside the module: VO+ and VO- are the positive and negative terminals of 24VDC respectively;
8. Extension interface: This interface is the base for inserting pin, which can be used to extend RPC2000 series extension modules;
9. Module power supply: L, N, GND respectively are the fire line, zero line and protective ground terminal of AC220V power supply;
10. Module output terminal: it is composed of 1L power supply drive end and output point Q, and the terminal is relay output;

Terminal tag definition specification
 
Terminal Terminal instructions Terminal Terminal instructions
* Undefined
A1+
The positive pole of the first RS485 interface
1L
Output common
B1-
The negative pole of the first RS485 interface
Q0.0
Normal Output terminal
A2+
The positive pole of the second RS485 interface
Q0.1
Normal Output terminal
B2-
The negative pole of the second RS485 interface
Q0.2
Normal Output terminal
1M
Input common
Q0.3
Normal Output terminal
I0.0
Normal input terminal
Q0.4 Normal Output terminal
I0.1
Normal input terminal
Q0.5 Normal Output terminal
I0.2
Normal input terminal
GND
GND I0.3 Normal input terminal
N
Neutral wire
I0.4
Normal input terminal/External interrupt input
L
Live wire
I0.5
Normal input terminal/External interrupt input
TX RS232 data sender
I1.6
Normal input terminal/External interrupt input
RX RS232 data receiver
I1.7
Normal input terminal/External interrupt input
GND RS232 ground terminal
I1.0
Normal input terminal
* Undefined
I1.1
Normal input terminal
CGND RS485 interface shielding ground
VO-
External power supply :positive
VO+
External power supply :negative

Input channel connection mode

CPU Module (10-CH 24VDC input &amp; 6-CH relay output) Support Codesys



Output channel connection mode

CPU Module (10-CH 24VDC input &amp; 6-CH relay output) Support Codesys



About CHINT

Founded in 1984, the Chint Group provides safe, reliable and stable industrial electrical equipment and solutions for energy efficient management systems. With 30 years of development it has grown to be Asia' s largest low*voltage electrical product supplier and is the leading brand of the whole industry chain in industrial electric in Asia. With three R&D centers located in Europe, North America and China, there are also branches in over 20 countries and more than 30.000 employees in the world. CHINT provides reliable products, system solutions and services to more than 100 countries worldwide.


CPU Module (10-CH 24VDC input &amp; 6-CH relay output) Support Codesys



•     3 Global Research Centers: Europe, North America, Asia Pacific
•     6 International Marketing & Sales Area: Asia Pacific, Middle East and Africa, Europe, Latin America, North America, China
•     9 Manufacturing Bases: China (Wenzhou, Shanghai, Hangzhou, Jiaxing, Xianyang, Jiuquan), Thailand, Egypt, Germany
•     22 Logistics Centers 14 International Subsidiaries 17 Marketing Offices in China 2300 Sales Companies


About Chitic

Chrtic Control Engineering Co.. Ltd. is a subsidiary company of Chint, and a leading provider of automation & control technologies and applications in China that helps the industry customers to improve operating safety, reliability and efficiency. Chitic has series of products including PCS1800 DCS, TDCS9200 DCS and CTS700 DCS, information platform for water company, control system for high speed rapier loom, drive system of switched reluctance motor, solar energy monitoring system, computing cloud center for new energy; etc. Chitic control system won 2006 National Science and Technology Progress Awards of China, CTS700 DCS won the award of 2010 Innovative Product of China. Chitic headquarter is located at the beautiful city of Hangzhou, two hours drive from Shanghai. Chitic has its own science & technology park, Chitic Park, which covers about six thousand square meters.

Our Business Sector
CPU Module (10-CH 24VDC input &amp; 6-CH relay output) Support Codesys




Typical Reference
CPU Module (10-CH 24VDC input &amp; 6-CH relay output) Support Codesys




 

 

Electrical Control System

PNEUTEC.IT, 2023