MPU-6050 SENSOR MPU6050 DMP Inertial Measurement Units 6-Axis MEMS

Description

MPU-6050: 6-Axis MEMS MotionTracking Device with DMP - Tape and Reel

Package: QFN-24

Mfr. Part#: MPU-6050

Mfr.: INVENSENSE
Datasheet:  (e-mail or chat us for PDF file)

ROHS Status: 

Quality: 100% Original

Warranty: 180 days

 

MotionInterface™ is becoming a "must-have" function being adopted by smartphone and tablet manufacturers due to the enormous value it adds to the end user experience. In smartphones, it finds use in applications such as gesture commands for applications and phone control, enhanced gaming, augmented reality, panoramic photo capture and viewing, and pedestrian and vehicle navigation. With its ability to precisely and accurately track user motions, MotionTracking technology can convert handsets and tablets into powerful 3D intelligent devices that can be used in applications ranging from health and fitness monitoring to location-based services. Key requirements for MotionInterface enabled devices are small package size, low power consumption, high accuracy and repeatability, high shock tolerance, and application specific performance programmability - all at a low consumer price point.

Key Features

• Digital-output X-, Y-, and Z-Axis angular rate sensors (gyroscopes) with a user-programmable fullscale range of ±250, ±500, ±1000, and ±2000°/sec
• External sync signal connected to the FSYNC pin supports image, video and GPS synchronization
• Integrated 16-bit ADCs enable simultaneous sampling of gyros
• Enhanced bias and sensitivity temperature stability reduces the need for user calibration
• Improved low-frequency noise performance
• Digitally-programmable low-pass filter
• Gyroscope operating current: 3.6mA
• Standby current: 5µA
• Factory calibrated sensitivity scale factor
• User self-test

• Digital-output triple-axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
• Integrated 16-bit ADCs enable simultaneous sampling of accelerometers while requiring no external multiplexer
• Accelerometer normal operating current: 500µA
• Low power accelerometer mode current: 10µA at 1.25Hz, 20µA at 5Hz, 60µA at 20Hz, 110µA at 40Hz
• Orientation detection and signaling
• Tap detection
• User-programmable interrupts
• High-G interrupt
• User self-test

• 9-Axis MotionFusion by the on-chip Digital Motion Processor (DMP)
• Auxiliary master I2C bus for reading data from external sensors (e.g., magnetometer)
• 3.9mA operating current when all 6 motion sensing axes and the DMP are enabled
• VDD supply voltage range of 2.375V-3.46V
• Flexible VLOGIC reference voltage supports multiple I 2C interface voltages (MPU-6050 only)
• Smallest and thinnest QFN package for portable devices: 4x4x0.9mm
• Minimal cross-axis sensitivity between the accelerometer and gyroscope axes
• 1024 byte FIFO buffer reduces power consumption by allowing host processor to read the data in bursts and then go into a low-power mode as the MPU collects more data
• Digital-output temperature sensor
• User-programmable digital filters for gyroscope, accelerometer, and temp sensor
• 10,000 g shock tolerant
• 400kHz Fast Mode I2C for communicating with all registers
• 1MHz SPI serial interface for communicating with all registers (MPU-6000 only)
• 20MHz SPI serial interface for reading sensor and interrupt registers (MPU-6000 only)

Company Product Line

 

Certificates



Product Packing details

• Located in Shenzhen, the electronic market center of China.
• 100% guarantee components quality: Genuine Original.
• Sufficient stock on your urgent demand.
• Sophisticated colleagues help you solve problems to reduce your risk with on-demand manufacturing
• Faster shipment: In stock components can ship the same day .
• 24 Hours service 

Notice:

1. Product images are for reference only.
2. You can contact sales person to apply for a better price.
3.  For more products, Pls do not hesitate to contact our Sales team.