Piping system | |||||||||
External water inlet pipe: There is one external water inlet on the back side of the pump, the pipe diameter is
Φ
150mm, the outer suction pipe is connected, and the inner buckle
Interface (small cover seal); suction pipe Φ 150 × 4m (2). |
|||||||||
Inner water inlet pipe: 1
Φ
150mm rear inlet water, the tank enters the fire pump, and installs 1
Φ
150mm
Butterfly valve, connecting liquid tank and water pump. |
|||||||||
Water outlet pipe: 2
Φ
80mm ball valves and 2
Φ
65mm ball valve controlled atmospheric pressure outlets;
1 Φ 89mm gun line, using Φ 80mm flexible joint, and using Φ 80mm Ball valve control. |
|||||||||
Water injection pipeline: 1
Φ
50mm internal water injection pipeline, water can be directly injected into the tank through the water pump;
There is one external water inlet on each side of the truck body. |
|||||||||
Remaining water pipeline: To protect the water pump and each ball valve, install a drain valve at the lowest point of the pipeline. | |||||||||
Cooling water line: The power take-off is used to cope with various complicated situations, and is equipped with a cooling water line and a stainless steel ball valve. | |||||||||
Foam proportional mixer: Type: ring pump type Mix ratio: 6% | |||||||||
Equipment box and pump room | |||||||||
Material: the skeleton is made of high quality steel | |||||||||
Structure: The partition inside the equipment box is made of steel structure, which is firm and reliable, improving space utilization and variability. | |||||||||
Opening the door: There are aluminum alloy rolling shutters on the left and right sides of the equipment box, which are light and reliable and have low noise. | |||||||||
Electrical system | |||||||||
License plate holder: meets the requirements of GB4785 and meets the license lighting requirements. | |||||||||
Cab top: equipped with long row of luxury p olice lights, alarm power is 100W; alarm, p olice
The lamp and strobe circuit are independent additional circuits, and the controller is installed in the cab. |
|||||||||
Safety sign light: 4 signs on each side of the lower part, one turn signal on each side, with a position light. | |||||||||
General technical requirements | |||||||||
1. All operating switches, instruments, equipment racks and vehicles have nameplate signs that conform to the specifications; | |||||||||
2. The vehicle performance complies with the provisions of GB7956 " Fire Engine Performance Requirements and Test Methods " ; | |||||||||
3. The quality of the liquid tank complies with the provisions of GA39; | |||||||||
4.English Operation Manuals | |||||||||
Components And Accessories | |||||||||
Category | Serial number | Equipment name | Quantity | Unit | |||||
Fire extinguisher | 1 | Water Suction Pipe | 4000mm*2 | pcs | |||||
2 | Water Strainer | 1 | pcs | ||||||
3 | Water Segregator | 1 | pcs | ||||||
4 | Water Collector | 1 | pcs | ||||||
5 | ∈ 65 × 20m Soft-wall fire hose | 8 | pcs | ||||||
6 | ∈ 80 × 20m Soft-wall fire hose | 4 | pcs | ||||||
7 | Adapter Joint | 2 | pcs | ||||||
8 | Irregular interface Joint | 1 | pcs | ||||||
9 | Fire Axe | 1 | pcs | ||||||
10 | Hose protector | 4 | pcs | ||||||
11 | Groud Hydrant-wrench | 1 | pcs | ||||||
12 | Undergroud hydrant-wrench | 1 | pcs | ||||||
13 | Suction pipe wrench | 2 | pcs | ||||||
14 | Fire water gun | 2 | pcs | ||||||
15 | Fire bucket | 1 | pcs | ||||||
16 | 4M Aluminum Ladder | 1 | pcs | ||||||
17 | Foam gun | 1 | pcs | ||||||
Demolition rescue tool | 1 | Fire extinguisher | 1 | pcs | |||||
2 | shovel | 1 | pcs | ||||||
3 | Fire waist axe | 1 | pcs | ||||||
4 | Tick | 1 | pcs | ||||||
5 | Shovel | 1 | pcs |