Factory Price 80W/100W/120W DC36V 3000-6500K Aluminum LED Streets Overpasses Sidewalks Squares Schools Outdoor Light

Product details

Lum-iled /Os-rams chips, high brightness, low light decay & long life-time

International driver brand, overheat protection, high convert efficiency, high PF & surge protection, (1-10V,DALI2.0)

Die-casting technology with ADC12, excellent thermal management and balance the internal & external temperature, reduce chip Tj and light decay.

4mm tempered glass cover with 94% light transmi ance, IK08.

Light Distribution: T2-M, T3-M. Pole installation. operation temperature: -35C-
 

WATERPROOF

1 IP66 waterproof

2 Safer outdoor use

Product dimension:
                                                                                                  80W/100W/120W

Photometry
 

These parameters [Lav, U0, UI, TI, SR] can meet the requirements. In accordance with CIE140 / EN13201 (ME3 ~ ME5) requirements, through simulation, this narrow light distribution is ideal for illuminating sidewalks, trails and sidewalks.

Narrow light distribution can also be used for dual lanes. You can use this type of light distribution on wide sidewalks, side roads and auxiliary roads. According to the requirements of CIE140 / EN13201 (ME3 ~ ME5), by simulation, these parameters [Lav, U0, UI, TI, SR] can meet the requirements

The wide light distribution is ideal for freeways, expressways and urban arteries. The step height ratio of the point can reach 3.5. According to the requirements of CIE140 / EN13201 (ME1 ~ ME2), through simulation, these parameters [Lav, U0, UI, TI, SR] can meet the requirements

The wide light distribution is also ideal for multi-lane roads. You can use wide light distribution for multi-lane arteries, downtown roads, etc. The pitch height ratio of the point can reach 3.5. (ME1~ ME2), through simulation, these parameters [Lav, U0, UI, TI, SR] can meet the requirement

Extra Accessory

What is the general power of LED street lights, and how is the life?

The specific power of the LED street lamp needs to be determined according to the specific situation of the road, the different height of the street lamp pole uses different power, like 6 meters using 30W~60W, 8 meters using 60W~100W between the lamp, professional LED street lamp manufacturers will give a standard solution after the investigation of the road situation.
The theoretical life of the led light source is very long, but the overall life of a lamp is not simply the life of the light source, the lamp also includes the influence of the drive and the lens part. Therefore, the life of the final street lamp should be limited to the shortest life of all the lamp parts. At present, the life of the good driving power supply and the lens made of silicon material in China can reach 50,000 hours.
The power saving part. Take 120w LED lamps instead of 250w high-pressure sodium lamps as an example. The actual power of the high-pressure sodium lamp needs to be multiplied by the coefficient of the ballast, calculated according to 1.17, the actual power is 292.5w. In the entire line of the lamp, there is also a reactive loss, line loss, transformer loss, etc., in this case, it is not increased, and only compared with the lower value in theory. LED whole lamp power = light source power + power loss, now a good manufacturer LED drive efficiency can do about 97%, almost negligible. Taking 100 street lights for 12h as an example, the daily power consumption of high-pressure sodium lamps =292.5*100/1000*12=351 degrees. LED daily power consumption =120*100/1000*12=144 degrees, if coupled with the intelligent dimming of FLED street lights, the entire energy saving rate is at least 70%
In general, led street lights are brighter than traditional high-pressure sodium lamps with the same power, and when configuring LED light sources, they can not be configured in accordance with old concepts. At the same time, it also saves electricity and energy than high-pressure sodium lamps.

FAQ:

Q1: Are you a manufacturer?
MF: Yes, we are a manufacturer with our own factory. We have over 14 years of experience in research and development, as well as manufacturing, and we operate based on ISO quality management since 2009.

Q2: Can I order a sample of the LED High Mast Light?
MF: Yes, we welcome sample orders to test and check the quality of our products. Mixed samples are also acceptable.

Q3: What is the lead time for the LED High Mast Light?
MF: For sample orders, the lead time is 3-7 days, and for mass production orders, it is 15-25 days. The exact lead time depends on the order quantities.

Q4: How do you ship the finished products?
MF: We offer optional shipping methods such as by SEA, AIR, or Express (DHL, UPS, FedEx, TNT, etc.).

Q5: Can I print my logo on the LED High Mast Light?
MF: Yes, we provide OEM service to our customers. We can help to make the label and color box according to your requirements.

Q6: How do I proceed with an order for the LED High Mast Light?
MF: Firstly, please let us know your detailed requirements and application environment. Secondly, we will recommend some suitable products and solutions to you based on your request. Thirdly, after confirming all the details, customers will issue a purchase order and make the payment to confirm, and then we will start production and arrange shipment.

Q7: How do you handle defective products?
MF: All of our products are produced in strict quality control systems, and the defective rate is less than 0.2% according to our shipment records. We offer a 5-year warranty for this product. If there is any defect during the warranty period, please provide pictures or videos of the defective lights in working situations, and we will ship new lights to you within a few days or together with your next order.